Schedule Services

 

 

How do you really feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently available, the job can move immediately; if you need to open a wall surface to remove the old tub and also position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have qualified on your own for the task and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to consider using one before you begin. Chances are you might need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your shower room if you have currently purchased a brand-new tub and do not need to transform the plan of your previous water supply pipelines.
Your devices as well as material list must comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Planning for the Setup

First of all, the sustaining framework supplied with the bathroom ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last position.

 

 

Removing Old Touches

If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic because of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Setting up the Bathtub

Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub must wait until the tub has actually been utilized at the very least once as this will certainly settle it right into its final placement.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washers are in location in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with wetness and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can fracture rather early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is recommended to fit the ceramic tiles using waterproof or water-proof adhesive and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I discovered that content about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while surfing around the internet. Enjoyed reading our write up? Please share it. Help others check it out. We love reading our article about How to Install a Bathtub.

Book A Service Call